Graduate Aptitude Test in Engineering (GATE) is an all India examination conducted jointly by the Indian Institute of Science and seven IITs (IIT Bombay, IIT Delhi, IIT Guwahati, IIT Kanpur, IIT Kharagpur, IIT Madras and IIT Roorkee) on behalf of the National Coordination Board – GATE, Department of Higher Education, Ministry of Human Resource Development (MHRD), Government of India.

(GATE primanarily tests the comprehensive understanding of the candidate in various undergraduate subjects in Engineering/ Technology/Architecture and post-graduate level in a particular subject in the exam across several years. The GATE score is used for admissions to post-graduate programs (e.g., M.E., M.Tech, Direct Ph.D.) in Indian institutes of higher education with financial assistance provided by MHRD and other Government agencies.The score may also be used by public and private sector undertakings for employment screening purposes.

**OBJECTIVE OF GATE**

- Identify, at the National level, meritorious and motivated candidates for admission to postgraduate program in engineering, technology, architecture and science.
- Serve as mandatory qualification for the MHRD scholarship / assistantship.
- Serve as a benchmark for normalization of the undergraduate engineering education in the country.

The GATE score of a candidate reflects the relative performance level of a candidate. The score is used for admissions to various post-graduate program (eg. M.E., M.Tech, direct Ph.D.) in Indian higher education institutes with financial assistance provided by MHRD and other Government agencies. The score may also be used by Public sector units(PSUs) for employment screening purposes.

Over 500 institutes including the IISc, IITs and NITs require GATE score for admission to their ME, M.Tech and MS Programs.

A host of PSUs use GATE Scores for jobs in these organizations.

Some non-Indian universities like the National University of Singapore, Nanyang Technological University in Singapore and some technical universities in Germany also identify GATE score as a parameter for judging the quality of the candidates for admission into their Masters and Ph.D. programs.

GATE qualified students are eligible for stipend of Rs. 12400/- per month on M.tech admission.

**The following categories of candidates are eligible to appear for GATE :**

- Bachelor's degree holders in Engineering/Technology/ Architecture (4 years after 10+2) and those who are in the final year of such programmes.
- Bachelor's degree holders in Engineering/Technology/Architecture (Post-B.Sc./Post-Diploma) and those who are in the final year of such programmes.
- Master's degree holders in any branch of Science/Mathematics/ Statistics/Computer Applications or equivalent and those who are in the final year of such programmes.
- Candidates in the second or higher year of the Four-year Integrated Master's degree programmer (Post-B.Sc.) in Engineering/Technology.
- Candidates in the fourth or higher year of Five-year Integrated Master's degree programme or Dual Degree programme in Engineering/Technology.
- Candidates with qualifications obtained through examinations conducted by professional societies recognized by UPSC/AICTE (e.g. AMIE by Institute of Engineers (India); AMICE by Institute of Civil Engineers (India)) as equivalent to B.E./B.Tech. Those who have completed section A or equivalent of such professional courses are also eligible.

The GATE examination for the papers AE, AG, AR, BT, CE, CH, CS,CY, EC, EE, EY, GG, IN,MA, ME,MN, MT, PH, PI, TF, XE and XL will be conducted ONLINE using computers .In all the papers, there will be a total of 65 questions carrying 100 marks, out of which 10 questions carrying a total of 15 marks are in General Aptitude (GA).

In the papers bearing the codes AE, AG, BT, CE, CH, CS, EC, EE, IN, ME, MN, MT, PI, TF and XE, the Engineering Mathematics will carry around 15% of the total marks, the General Aptitude section will carry 15% of the total marks and the remaining percentage of the total marks is devoted to the subject of the paper.

In the papers bearing the codes AR, CY, EY, GG, MA, PH and XL, the General Aptitude section will carry 15% of the total marks and the remaining 85% of the total marks is devoted to the subject of the paper.

** GATE paper contain questions of two different types**

(i) Multiple Choice Questions (MCQ) carrying 1 or 2 marks each in all papers and sections. These questions are objective in nature, and each will have a choice of four answers, out of which the candidate has to mark the correct answer(s).

(ii) Numerical Answer Questions of 1 or 2 marks each in all papers and sections. For these questions the answer is a real number, to be entered by the candidate using the virtual keypad. No choices will be shown for this type of questions.

**The questions in a paper may be designed to test the following abilities:**

**(i)Recall:** These are based on facts, principles, formulae or laws of the discipline of the paper. The candidate is expected to be able to obtain the answer either from his/her memory of the subject or at most from a one-line computation.

**(ii) Comprehension:** These questions will test the candidate’s understanding of the basics of his/her field, by requiring him/her to draw simple conclusions from fundamental ideas.

**(iii) Application:** In these questions, the candidate is expected to apply his/her knowledge either through computation or by logical reasoning.

**(iv) Analysis and Synthesis:** In these questions, the candidate is presented with data, diagrams, images etc. that require analysis before a question can be answered. A Synthesis question might require the candidate to compare two or more pieces of information. Questions in this category could, for example, involve candidates in recognizing unstated assumptions, or separating useful information from irrelevant information.

SALE OF INFORMATION BROCHURE AND OFFLINE APPLICATION FORM/ONLINE APPLICATIO FORM SUBMISSION. | SEPTEMBER |

LAST DATE OF ISSUE OF INFORMATION BROCHURE ANDAPPLICATION FORM BY POST FROM GATE OFFICES, BANKCOUNTERS, AND GATE OFFICE COUNTERS | OCTOBER |

LAST DATE OF SUBMISSION OF ONLINE APPLICATION FORM | OCTOBER |

LAST DATE FOR SUBMISSION OF RECEIPT OF COMPLETED OFFLINE/ONLINE APPLICATION FORM AT RESPECTIVE ZONALGATE OFFICE. | OCTOBER |

DATE OF GATE EXAM. | LAST WEEKEND OF JANUARY MONTH & FIRST WEEKEND IF FEBRUARY MONTH |

DATE OF GATE Result. | MID MARCH |

The Qualifying Score is the minimum mark that needs to be secured to become eligible for availing assistant ships provided by MHRD, GOI. The qualifying score for general category in each paper is (a + s) or 25, whichever is higher, where a and s are the average and standard deviation of marks of all candidates in a particular paper, with all marks less than zero, converted to zero. The qualifying scores for SC/ST/PD/OBC categories would be 2/3, 2/3, 2/3 and 9/10, respectively, of the general category qualifying score.

**GATE SCORECARD:** GATE scorecard is valid for THREE YEARS from the date of announcement of the GATE results (March 15 at 10.00 hrs.). There is no provision for additional GATE scorecards.

GATE Paper Code |
GATE Paper |
Qualifying Marks (General) |
Qualifying Marks (OBCNCL) |
Qualifying Marks (SC/ST/PwD) |
---|---|---|---|---|

EC | Electronics and Communication | 25 | 22.5 | 16.67 |

CS | Computer Science and IT | 25 | 22.5 | 16.67 |

ME | Mechanical Engineering | 26.6 | 29.6 | 19.7 |

EE | Electrical Engineering | 25.1 | 22.25 | 16.67 |

IN | Instrumentation Engineering | 36.1 | 28.4 | 21 |

CE | Civil Engineering | 22.5 | 22.5 | 16.6 |

GATE Paper Code |
GATE Paper |
Qualifying Marks (General) |
Qualifying Marks (OBCNCL) |
Qualifying Marks (SC/ST/PwD) |
---|---|---|---|---|

EC | Electronics and Communication | 25 | 22.5 | 16.67 |

CS | Computer Science and IT | 25 | 22.5 | 16.67 |

ME | Mechanical Engineering | 32.73 | 29.46 | 21.82 |

EE | Electrical Engineering | 25.1 | 22.25 | 16.67 |

IN | Instrumentation Engineering | 25.45 | 22.9 | 16.96 |

CE | Civil Engineering | 25 | 22.5 | 16.67 |

GATE Paper Code |
GATE Paper |
Qualifying Marks (General) |
Qualifying Marks (OBCNCL) |
Qualifying Marks (SC/ST/PwD) |
---|---|---|---|---|

EC | Electronics and Communication | 25.56 | 23.01 | 17.04 |

CS | Computer Science and IT | 25 | 22.5 | 16.67 |

ME | Mechanical Engineering | 28.86 | 25.97 | 19.84 |

EE | Electrical Engineering | 25.1 | 22.25 | 16.67 |

IN | Instrumentation Engineering | 25 | 22.5 | 16.67 |

CE | Civil Engineering | 26.57 | 23.91 | 17.71 |

**Section 1: Engineering Mathematics**

**Linear Algebra :** Matrix algebra; Systems of linear equations; Eigen values and Eigen vectors.

**Calculus :** Functions of single variable; Limit, continuity and differentiability; Mean value theorems, local maxima and minima, Taylor and Maclaurin series; Evaluation of definite and indefinite integrals, application of definite integral to obtain area and volume; Partial derivatives; Total derivative; Gradient, Divergence and Curl, Vector identities, Directional derivatives, Line, Surface and Volume integrals, Stokes, Gauss and Green’s theorems.

**Ordinary Differential Equation (ODE):** First order (linear and non-linear) equations; higher order linear equations with constant coefficients; Euler-Cauchy equations; Laplace transform and its application in solving linear ODEs; initial and boundary value problems.

**Partial Differential Equation (PDE):** Fourier series; separation of variables; solutions of one-dimensional diffusion equation; first and second order one-dimensional wave equation and two-dimensional Laplace equation.

**Probability and Statistics :** Definitions of probability and sampling theorems; Conditional probability; Discrete Random variables: Poisson and Binomial distributions; Continuous random variables: normal and exponential distributions; Descriptive statistics - Mean, median, mode and standard deviation; Hypothesis testing.

**Numerical Methods:** Accuracy and precision; error analysis. Numerical solutions of linear and non-linear algebraic equations; Least square approximation, Newton’s and Lagrange polynomials, numerical differentiation, Integration by trapezoidal and Simpson’s rule, single and multi-step methods for first order differential equations.

**Section 2: Structural Engineering**

**Engineering Mechanics: **System of forces, free-body diagrams, equilibrium equations; Internal forces in structures; Friction and its applications; Kinematics of point mass and rigid body; Centre of mass; Euler’s equations of motion; Impulse-momentum; Energy methods; Principles of virtual work.

**Solid Mechanics:** Bending moment and shear force in statically determinate beams; Simple stress and strain relationships; Theories of failures; Simple bending theory, flexural and shear stresses, shear centre; Uniform torsion, buckling of column, combined and direct bending stresses.

**Structural Analysis:** Statically determinate and indeterminate structures by force/ energy methods; Method of superposition; Analysis of trusses, arches, beams, cables and frames; Displacement methods: Slope deflection and moment distribution methods; Influence lines; Stiffness and flexibility methods of structural analysis.

**Construction Materials and Management:** Construction Materials: Structural steel - composition, material properties and behaviour; Concrete - constituents, mix design, short-term and long-term properties; Bricks and mortar; Timber; Bitumen. Construction Management: Types of construction projects; Tendering and construction contracts; Rate analysis and standard specifications; Cost estimation; Project planning and network analysis - PERT and CPM.

**Concrete Structures:** Working stress, Limit state and Ultimate load design concepts; Design of beams, slabs, columns; Bond and development length; Prestressed concrete; Analysis of beam sections at transfer and service loads.

**Steel Structures:** Working stress and Limit state design concepts; Design of tension and compression members, beams and beam- columns, column bases; Connections - simple and eccentric, beam-column connections, plate girders and trusses; Plastic analysis of beams and frames.

**Section 3: Geotechnical Engineering**

**Soil Mechanics:** Origin of soils, soil structure and fabric; Three-phase system and phase relationships, index properties; Unified and Indian standard soil classification system; Permeability - one dimensional flow, Darcy’s law; Seepage through soils - two-dimensional flow, flow nets, uplift pressure, piping; Principle of effective stress, capillarity, seepage force and quicksand condition; Compaction in laboratory and field conditions; One-dimensional consolidation, time rate of consolidation; Mohr’s circle, stress paths, effective and total shear strength parameters, characteristics of clays and sand.

**Foundation Engineering:** Sub-surface investigations - scope, drilling bore holes, sampling, plate load test, standard penetration and cone penetration tests; Earth pressure theories - Rankine and Coulomb; Stability of slopes - finite and infinite slopes, method of slices and Bishop’s method; Stress distribution in soils - Boussinesq’s and Westergaard’s theories, pressure bulbs; Shallow foundations - Terzaghi’s and Meyerhoff’s bearing capacity theories, effect of water table; Combined footing and raft foundation; Contact pressure; Settlement analysis in sands and clays; Deep foundations - types of piles, dynamic and static formulae, load capacity of piles in sands and clays, pile load test, negative skin friction.

**Section 4: Water Resources Engineering**

**Fluid Mechanics:**Properties of fluids, fluid statics; Continuity, momentum, energy and corresponding equations; Potential flow, applications of momentum and energy equations; Laminar and turbulent flow; Flow in pipes, pipe networks; Concept of boundary layer and its growth.

**Hydraulics:** Forces on immersed bodies; Flow measurement in channels and pipes; Dimensional analysis and hydraulic similitude; Kinematics of flow, velocity triangles; Basics of hydraulic machines, specific speed of pumps and turbines; Channel Hydraulics - Energy-depth relationships, specific energy, critical flow, slope profile, hydraulic jump, uniform flow and gradually varied flow

**Hydrology:** Hydrologic cycle, precipitation, evaporation, evapo-transpiration, watershed, infiltration, unit hydrographs, hydrograph analysis, flood estimation and routing, reservoir capacity, reservoir and channel routing, surface run-off models, ground water hydrology - steady state well hydraulics and aquifers; Application of Darcy’s law.

**Irrigation:** Duty, delta, estimation of evapo-transpiration; Crop water requirements; Design of lined and unlined canals, head works, gravity dams and spillways; Design of weirs on permeable foundation; Types of irrigation systems, irrigation methods; Water logging and drainage; Canal regulatory works, cross-drainage structures, outlets and escapes.

**Section 5: Environmental Engineering**

**Water and Waste Water :** Quality standards, basic unit processes and operations for water treatment. Drinking water standards, water requirements, basic unit operations and unit processes for surface water treatment, distribution of water. Sewage and sewerage treatment, quantity and characteristics of wastewater. Primary, secondary and tertiary treatment of wastewater, effluent discharge standards. Domestic wastewater treatment, quantity of characteristics of domestic wastewater, primary and secondary treatment. Unit operations and unit processes of domestic wastewater, sludge disposal.

**Air Pollution:** Types of pollutants, their sources and impacts, air pollution meteorology, air pollution control, air quality standards and limits.

Municipal Solid Wastes: Characteristics, generation, collection and transportation of solid wastes, engineered systems for solid waste management (reuse/ recycle, energy recovery, treatment and disposal).

**Noise Pollution:** Impacts of noise, permissible limits of noise pollution, measurement of noise and control of noise pollution.

**Section 6: Transportation Engineering**

**Transportation Infrastructure :** Highway alignment and engineering surveys; Geometric design of highways - cross-sectional elements, sight distances, horizontal and vertical alignments; Geometric design of railway track; Airport runway length, taxiway and exit taxiway design.

**Highway Pavements:** Highway materials - desirable properties and quality control tests; Design of bituminous paving mixes; Design factors for flexible and rigid pavements; Design of flexible pavement using IRC: 37-2012; Design of rigid pavements using IRC: 58-2011; Distresses in concrete pavements.

**Traffic Engineering:** Traffic studies on flow, speed, travel time - delay and O-D study, PCU, peak hour factor, parking study, accident study and analysis, statistical analysis of traffic data; Microscopic and macroscopic parameters of traffic flow, fundamental relationships; Control devices, signal design by Webster’s method; Types of intersections and channelization; Highway capacity and level of service of rural highways and urban roads.

**Section 7: Geomatics Engineering**

Principles of surveying; Errors and their adjustment; Maps - scale, coordinate system; Distance and angle measurement - Levelling and trigonometric levelling; Traversing and triangulation survey; Total station; Horizontal and vertical curves. Photogrammetry - scale, flying height; Remote sensing - basics, platform and sensors, visual image interpretation; Basics of Geographical information system (GIS) and Geographical Positioning system (GPS).

.**Section 1: Engineering Mathematics**

**Linear Algebra:** Matrix algebra, systems of linear equations, eigen values and eigenvectors.

**Calculus:** Functions of single variable, limit, continuity and differentiability, mean value theorems, indeterminate forms; evaluation of definite and improper integrals; double and triple integrals; partial derivatives, total derivative, Taylor series (in one and two variables), maxima and minima, Fourier series; gradient, divergence and curl, vector identities, directional derivatives, line, surface and volume integrals, applications of Gauss, Stokes and Green’s theorems.

**Differential equations:** First order equations (linear and nonlinear); higher order linear differential equations with constant coefficients; Euler-Cauchy equation; initial and boundary value problems; Laplace transforms; solutions of heat, wave and Laplace's equations.

**Complex variables:** Analytic functions; Cauchy-Riemann equations; Cauchy’s integral theorem and integral formula; Taylor and Laurent series.

**Probability and Statistics:** Definitions of probability, sampling theorems, conditional probability; mean, median, mode and standard deviation; random variables, binomial, Poisson and normal distributions.

**Numerical Methods:** Numerical solutions of linear and non-linear algebraic equations; integration by trapezoidal and Simpson’s rules; single and multi-step methods for differential equations.

**Section 2: Applied Mechanics and Design**

**Engineering Mechanics:** Free-body diagrams and equilibrium; trusses and frames; virtual work; kinematics and dynamics of particles and of rigid bodies in plane motion; impulse and momentum (linear and angular) and energy formulations, collisions.

**Mechanics of Materials:** Stress and strain, elastic constants, Poisson's ratio; Mohr’s circle for plane stress and plane strain; thin cylinders; shear force and bending moment diagrams; bending and shear stresses; deflection of beams; torsion of circular shafts; Euler’s theory of columns; energy methods; thermal stresses; strain gauges and rosettes; testing of materials with universal testing machine; testing of hardness and impact strength.

**Theory of Machines:** Displacement, velocity and acceleration analysis of plane mechanisms; dynamic analysis of linkages; cams; gears and gear trains; flywheels and governors; balancing of reciprocating and rotating masses; gyroscope.

**Vibrations:** Free and forced vibration of single degree of freedom systems, effect of damping; vibration isolation; resonance; critical speeds of shafts.

**Machine Design:** Design for static and dynamic loading; failure theories; fatigue strength and the S-N diagram; principles of the design of machine elements such as bolted, riveted and welded joints; shafts, gears, rolling and sliding contact bearings, brakes and clutches, springs.

**Section 3: Fluid Mechanics and Thermal Sciences**

**Fluid Mechanics:** Fluid properties; fluid statics, manometry, buoyancy, forces on submerged bodies, stability of floating bodies; control-volume analysis of mass, momentum and energy; fluid acceleration; differential equations of continuity and momentum; Bernoulli’s equation; dimensional analysis; viscous flow of incompressible fluids, boundary layer, elementary turbulent flow, flow through pipes, head losses in pipes, bends and fittings.

**Heat-Transfer:** Modes of heat transfer; one dimensional heat conduction, resistance concept and electrical analogy, heat transfer through fins; unsteady heat conduction, lumped parameter system, Heisler's charts; thermal boundary layer, dimensionless parameters in free and forced convective heat transfer, heat transfer correlations for flow over flat plates and through pipes, effect of turbulence; heat exchanger performance, LMTD and NTU methods; radiative heat transfer, Stefan-Boltzmann law, Wien's displacement law, black and grey surfaces, view factors, radiation network analysis.

**Thermodynamics:** Thermodynamic systems and processes; properties of pure substances, behaviour of ideal and real gases; zeroth and first laws of thermodynamics, calculation of work and heat in various processes; second law of thermodynamics; thermodynamic property charts and tables, availability and irreversibility; thermodynamic relations.

**Applications:** Power Engineering: Air and gas compressors; vapour and gas power cycles, concepts of regeneration and reheat. I.C. Engines: Air-standard Otto, Diesel and dual cycles. Refrigeration and air-conditioning: Vapour and gas refrigeration and heat pump cycles; properties of moist air, psychrometric chart, basic psychrometric processes. Turbomachinery: Impulse and reaction principles, velocity diagrams, Pelton-wheel, Francis and Kaplan turbines.

**Section 4: Materials, Manufacturing and Industrial Engineering**

**Engineering Materials:** Structure and properties of engineering materials, phase diagrams, heat treatment, stress-strain diagrams for engineering materials.

**Casting, Forming and Joining Processes:** Different types of castings, design of patterns, moulds and cores; solidification and cooling; riser and gating design. Plastic deformation and yield criteria; fundamentals of hot and cold working processes; load estimation for bulk (forging, rolling, extrusion, drawing) and sheet (shearing, deep drawing, bending) metal forming processes; principles of powder metallurgy. Principles of welding, brazing, soldering and adhesive bonding.

**Machining and Machine Tool Operations:** Mechanics of machining; basic machine tools; single and multi-point cutting tools, tool geometry and materials, tool life and wear; economics of machining; principles of non-traditional machining processes; principles of work holding, design of jigs and fixtures.

**Metrology and Inspection:** Limits, fits and tolerances; linear and angular measurements; comparators; gauge design; interferometry; form and finish measurement; alignment and testing methods; tolerance analysis in manufacturing and assembly.

**Computer Integrated Manufacturing:** Basic concepts of CAD/CAM and their integration tools.

**Production Planning and Control:** Forecasting models, aggregate production planning, scheduling, materials requirement planning.

**Inventory Control:** Deterministic models; safety stock inventory control systems.

**Operations Research:** Linear programming, simplex method, transportation, assignment, network flow models, simple queuing models, PERT and CPM.

**Section 1: Engineering Mathematics**

**Linear Algebra:** Vector space, basis, linear dependence and independence, matrix algebra, eigen values and eigen vectors, rank, solution of linear equations – existence and uniqueness.

**Calculus:** Mean value theorems, theorems of integral calculus, evaluation of definite and improper integrals, partial derivatives, maxima and minima, multiple integrals, line, surface and volume integrals, Taylor series.

**Differential Equations:** First order equations (linear and nonlinear), higher order linear differential equations, Cauchy's and Euler's equations, methods of solution using variation of parameters, complementary function and particular integral, partial differential equations, variable separable method, initial and boundary value problems.

**Vector Analysis:** Vectors in plane and space, vector operations, gradient, divergence and curl, Gauss's, Green's and Stoke's theorems.

**Complex Analysis:** Analytic functions, Cauchy's integral theorem, Cauchy's integral formula; Taylor's and Laurent's series, residue theorem.

**Numerical Methods:** Solution of nonlinear equations, single and multi-step methods for differential equations, convergence criteria.

**Probability and Statistics:** Mean, median, mode and standard deviation; combinatorial probability, probability distribution functions - binomial, Poisson, exponential and normal; Joint and conditional probability; Correlation and regression analysis.

**Section 2: Networks, Signals and Systems**

**Network solution methods:** nodal and mesh analysis; Network theorems: superposition, Thevenin and Norton’s, maximum power transfer; Wye‐Delta transformation; Steady state sinusoidal analysis using phasors; Time domain analysis of simple linear circuits; Solution of network equations using Laplace transform; Frequency domain analysis of RLC circuits; Linear 2‐port network parameters: driving point and transfer functions; State equations for networks.

**Continuous-time signals:** Fourier series and Fourier transform representations, sampling theorem and applications; Discrete-time signals: discrete-time Fourier transform (DTFT), DFT, FFT, Z-transform, interpolation of discrete-time signals; LTI systems: definition and properties, causality, stability, impulse response, convolution, poles and zeros, parallel and cascade structure, frequency response, group delay, phase delay, digital filter design techniques.

**Section 3: Electronic Devices**

**Energy bands in intrinsic and extrinsic silicon; Carrier transport:** diffusion current, drift current, mobility and resistivity; Generation and recombination of carriers; Poisson and continuity equations; P-N junction, Zener diode, BJT, MOS capacitor, MOSFET, LED, photo diode and solar cell; Integrated circuit fabrication process: oxidation, diffusion, ion implantation, photolithography and twin-tub CMOS process.

**Section 4: Analog Circuits**

Small signal equivalent circuits of diodes, BJTs and MOSFETs; Simple diode circuits: clipping, clamping and rectifiers; Single-stage BJT and MOSFET amplifiers: biasing, bias stability, mid-frequency small signal analysis and frequency response; BJT and MOSFET amplifiers: multi-stage, differential, feedback, power and operational; Simple op-amp circuits; Active filters; Sinusoidal oscillators: criterion for oscillation, single-transistor and op-amp configurations; Function generators, wave-shaping circuits and 555 timers; Voltage reference circuits; Power supplies: ripple removal and regulation.

**Section 5: Digital Circuits**

Number systems; Combinatorial circuits: Boolean algebra, minimization of functions using Boolean identities and Karnaugh map, logic gates and their static CMOS implementations, arithmetic circuits, code converters, multiplexers, decoders and PLAs; Sequential circuits: latches and flip‐flops, counters, shift‐registers and finite state machines; Data converters: sample and hold circuits, ADCs and DACs; Semiconductor memories: ROM, SRAM, DRAM; 8-bit microprocessor (8085): architecture, programming, memory and I/O interfacing.

**Section 6: Control Systems**

Basic control system components; Feedback principle; Transfer function; Block diagram representation; Signal flow graph; Transient and steady-state analysis of LTI systems; Frequency response; Routh-Hurwitz and Nyquist stability criteria; Bode and root-locus plots; Lag, lead and lag-lead compensation; State variable model and solution of state equation of LTI systems.

**Section 7: Communications**

Random processes: autocorrelation and power spectral density, properties of white noise, filtering of random signals through LTI systems; Analog communications: amplitude modulation and demodulation, angle modulation and demodulation, spectra of AM and FM, superheterodyne receivers, circuits for analog communications; Information theory: entropy, mutual information and channel capacity theorem; Digital communications: PCM, DPCM, digital modulation schemes, amplitude, phase and frequency shift keying (ASK, PSK, FSK), QAM, MAP and ML decoding, matched filter receiver, calculation of bandwidth, SNR and BER for digital modulation; Fundamentals of error correction, Hamming codes; Timing and frequency synchronization, inter-symbol interference and its mitigation; Basics of TDMA, FDMA and CDMA.

**Section 8: Electromagnetics**

Electrostatics; Maxwell’s equations: differential and integral forms and their interpretation, boundary conditions, wave equation, Poynting vector; Plane waves and properties: reflection and refraction, polarization, phase and group velocity, propagation through various media, skin depth; Transmission lines: equations, characteristic impedance, impedance matching, impedance transformation, S-parameters, Smith chart; Waveguides: modes, boundary conditions, cut-off frequencies, dispersion relations; Antennas: antenna types, radiation pattern, gain and directivity, return loss, antenna arrays; Basics of radar; Light propagation in optical fibers.

**Section 1: Engineering Mathematics**

**Linear Algebra:** Vector space, basis, linear dependence and independence, matrix algebra, eigen values and eigen vectors, rank, solution of linear equations – existence and uniqueness.

**Calculus:** Mean value theorems, Theorems of integral calculus, Evaluation of definite and improper integrals, Partial Derivatives, Maxima and minima, Multiple integrals, Fourier series, Vector identities, Directional derivatives, Line integral, Surface integral, Volume integral, Stokes’s theorem, Gauss’s theorem, Green’s theorem.

**Differential Equations:** First order equations (linear and nonlinear), Higher order linear differential equations with constant coefficients, Method of variation of parameters, Cauchy’s equation, Euler’s equation, Initial and boundary value problems, Partial Differential Equations, Method of separation of variables.

**Complex Analysis:** Analytic functions, Cauchy’s integral theorem, Cauchy’s integral formula, Taylor series, Laurent series, Residue theorem, Solution integrals.

**Probability and Statistics:** Sampling theorems, Conditional probability, Mean, Median, Mode, Standard Deviation, Random variables, Discrete and Continuous distributions, Poisson distribution, Normal distribution, Binomial distribution, Correlation analysis, Regression analysis.

**Numerical Methods:** Solutions of nonlinear algebraic equations, Single and Multi‐step methods for differential equations.

**Transform Theory:** Fourier Transform, Laplace Transform, z‐Transform.

**Section 2: Electric Circuits**

Network graph, KCL, KVL, Node and Mesh analysis, Transient response of dc and ac networks, Sinusoidal steady‐state analysis, Resonance, Passive filters, Ideal current and voltage sources, Thevenin’s theorem, Norton’s theorem, Superposition theorem, Maximum power transfer theorem, Two‐port networks, Three phase circuits, Power and power factor in ac circuits.

**Section 3: Electromagnetic Fields**

Coulomb's Law, Electric Field Intensity, Electric Flux Density, Gauss's Law, Divergence, Electric field and potential due to point, line, plane and spherical charge distributions, Effect of dielectric medium, Capacitance of simple configurations, Biot‐Savart’s law, Ampere’s law, Curl, Faraday’s law, Lorentz force, Inductance, Magnetomotive force, Reluctance, Magnetic circuits,Self and Mutual inductance of simple configurations.

**Section 4: Signals and Systems**

Representation of continuous and discrete‐time signals, Shifting and scaling operations, Linear Time Invariant and Causal systems, Fourier series representation of continuous periodic signals, Sampling theorem, Applications of Fourier Transform, Laplace Transform and z-Transform.

**Section 5: Electrical Machines**

Single phase transformer: equivalent circuit, phasor diagram, open circuit and short circuit tests, regulation and efficiency; Three phase transformers: connections, parallel operation; Auto‐transformer, Electromechanical energy conversion principles, DC machines: separately excited, series and shunt, motoring and generating mode of operation and their characteristics, starting and speed control of dc motors; Three phase induction motors: principle of operation, types, performance, torque-speed characteristics, no-load and blocked rotor tests, equivalent circuit, starting and speed control; Operating principle of single phase induction motors; Synchronous machines: cylindrical and salient pole machines, performance, regulation and parallel operation of generators, starting of synchronous motor, characteristics; Types of losses and efficiency calculations of electric machines.

**Section 6: Power Systems**

Power generation concepts, ac and dc transmission concepts, Models and performance of transmission lines and cables, Series and shunt compensation, Electric field distribution and insulators, Distribution systems, Per‐unit quantities, Bus admittance matrix, Gauss-Seidel and Newton-Raphson load flow methods, Voltage and Frequency control, Power factor correction, Symmetrical components, Symmetrical and unsymmetrical fault analysis, Principles of over‐current, differential and distance protection; Circuit breakers, System stability concepts, Equal area criterion.

**Section 7: Control Systems**

Mathematical modeling and representation of systems, Feedback principle, transfer function, Block diagrams and Signal flow graphs, Transient and Steady‐state analysis of linear time invariant systems, Routh-Hurwitz and Nyquist criteria, Bode plots, Root loci, Stability analysis, Lag, Lead and Lead‐Lag compensators; P, PI and PID controllers; State space model, State transition matrix.

**Section 8: Electrical and Electronic Measurements**

Bridges and Potentiometers, Measurement of voltage, current, power, energy and power factor; Instrument transformers, Digital voltmeters and multimeters, Phase, Time and Frequency measurement; Oscilloscopes, Error analysis.

**Section 9: Analog and Digital Electronics**

Characteristics of diodes, BJT, MOSFET; Simple diode circuits: clipping, clamping, rectifiers; Amplifiers: Biasing, Equivalent circuit and Frequency response; Oscillators and Feedback amplifiers; Operational amplifiers: Characteristics and applications; Simple active filters, VCOs and Timers, Combinational and Sequential logic circuits, Multiplexer, Demultiplexer, Schmitt trigger, Sample and hold circuits, A/D and D/A converters, 8085Microprocessor: Architecture, Programming and Interfacing.

**Section 10: Power Electronics**

Characteristics of semiconductor power devices: Diode, Thyristor, Triac, GTO, MOSFET, IGBT; DC to DC conversion: Buck, Boost and Buck-Boost converters; Single and three phase configuration of uncontrolled rectifiers, Line commutated thyristor based converters, Bidirectional ac to dc voltage source converters, Issues of line current harmonics, Power factor, Distortion factor of ac to dc converters, Single phase and three phase inverters, Sinusoidal pulse width modulation.

**Section 1: Engineering Mathematics**

**Linear Algebra:**Matrix algebra, systems of linear equations, Eigen values and Eigen vectors.

**Calculus:**Mean value theorems, theorems of integral calculus, partial derivatives, maxima and minima, multiple integrals, Fourier series, vector identities, line, surface and volume integrals, Stokes, Gauss and Green’s theorems.

**Differential Equations:**First order equation (linear and nonlinear), higher order linear differential equations with constant coefficients, method of variation of parameters, Cauchy’s and Euler’s equations, initial and boundary value problems, solution of partial differential equations: variable separable method.

Probability and Statistics: Sampling theorems, conditional probability, mean, median, mode and standard deviation, random variables, discrete and continuous distributions: normal, Poisson and binomial distributions.

Numerical Methods: Matrix inversion, solutions of non-linear algebraic equations, iterative methods for solving differential equations, numerical integration, regression and correlation analysis.

**Section 2: Electrical Circuits**

Voltage and current sources: independent, dependent, ideal and practical; v-i relationships of resistor, inductor, mutual inductor and capacitor; transient analysis of RLC circuits with dc excitation. Kirchoff’s laws, mesh and nodal analysis, superposition, Thevenin, Norton, maximum power transfer and reciprocity theorems. Peak-, average- and rms values of ac quantities; apparent-, active- and reactive powers; phasor analysis, impedance and admittance; series and parallel resonance, locus diagrams, realization of basic filters with R, L and C elements. One-port and two-port networks, driving point impedance and admittance, open-, and short circuit parameters.

**Section 3: Signals and Systems**

Periodic, aperiodic and impulse signals; Laplace, Fourier and z-transforms; transfer function, frequency response of first and second order linear time invariant systems, impulse response of systems; convolution, correlation. Discrete time system: impulse response, frequency response, pulse transfer function; DFT and FFT; basics of IIR and FIR filters.

**Section 4: Control Systems**

Feedback principles, signal flow graphs, transient response, steady-state-errors, Bode plot, phase and gain margins, Routh and Nyquist criteria, root loci, design of lead, lag and lead-lag compensators, state-space representation of systems; time-delay systems; mechanical, hydraulic and pneumatic system components, synchro pair, servo and stepper motors, servo valves; on-off, P, P-I, P-I-D, cascade, feedforward, and ratio controllers.

**Section 5: Analog Electronics**

Characteristics and applications of diode, Zener diode, BJT and MOSFET; small signal analysis of transistor circuits, feedback amplifiers. Characteristics of operational amplifiers; applications of opamps: difference amplifier, adder, subtractor, integrator, differentiator, instrumentation amplifier, precision rectifier, active filters and other circuits. Oscillators, signal generators, voltage controlled oscillators and phase locked loop.

**Section 6: Digital Electronics**

Combinational logic circuits, minimization of Boolean functions. IC families: TTL and CMOS. Arithmetic circuits, comparators, Schmitt trigger, multi-vibrators, sequential circuits, flip-flops, shift registers, timers and counters; sample-and-hold circuit, multiplexer, analog-to-digital (successive approximation, integrating, flash and sigma-delta) and digital-to-analog converters (weighted R, R-2R ladder and current steering logic). Characteristics of ADC and DAC (resolution, quantization, significant bits, conversion/settling time); basics of number systems, 8-bit microprocessor and microcontroller: applications, memory and input-output interfacing; basics of data acquisition systems.

**Section 7: Measurements**

SI units, systematic and random errors in measurement, expression of uncertainty - accuracy and precision index, propagation of errors. PMMC, MI and dynamometer type instruments; dc potentiometer; bridges for measurement of R, L and C, Q-meter. Measurement of voltage, current and power in single and three phase circuits; ac and dc current probes; true rms meters, voltage and current scaling, instrument transformers, timer/counter, time, phase and frequency measurements, digital voltmeter, digital multimeter; oscilloscope, shielding and grounding.

**Section 8: Sensors and Industrial Instrumentation**

Resistive-, capacitive-, inductive-, piezoelectric-, Hall effect sensors and associated signal conditioning circuits; transducers for industrial instrumentation: displacement (linear and angular), velocity, acceleration, force, torque, vibration, shock, pressure (including low pressure), flow (differential pressure, variable area, electromagnetic, ultrasonic, turbine and open channel flow meters) temperature (thermocouple, bolometer, RTD (3/4 wire), thermistor, pyrometer and semiconductor); liquid level, pH, conductivity and viscosity measurement.

**Section 9: Communication and Optical Instrumentation**

Amplitude- and frequency modulation and demodulation; Shannon's sampling theorem, pulse code modulation; frequency and time division multiplexing, amplitude-, phase-, frequency-, pulse shift keying for digital modulation; optical sources and detectors: LED, laser, photo-diode, light dependent resistor and their characteristics; interferometer: applications in metrology; basics of fiber optic sensing.

**Section 1: Engineering Mathematics**

**Discrete Mathematics:** Propositional and first order logic. Sets, relations, functions, partial orders and lattices. Groups. Graphs: connectivity, matching, coloring. Combinatorics: counting, recurrence relations, generating functions.

**Linear Algebra:** Matrices, determinants, system of linear equations, eigenvalues and eigenvectors, LU decomposition.

**Calculus:** Limits, continuity and differentiability. Maxima and minima. Mean value theorem. Integration.

**Probability:** Random variables. Uniform, normal, exponential, poisson and binomial distributions. Mean, median, mode and standard deviation. Conditional probability and Bayes theorem.

**Section 2: Digital Logic**

Boolean algebra. Combinational and sequential circuits. Minimization. Number representations and computer arithmetic (fixed and floating point).

**Section 3: Computer Organization and Architecture**

Machine instructions and addressing modes. ALU, data‐path and control unit. Instruction pipelining. Memory hierarchy: cache, main memory and secondary storage; I/O interface (interrupt and DMA mode).

**Section 4: Programming and Data Structures**

Programming in C. Recursion. Arrays, stacks, queues, linked lists, trees, binary search trees, binary heaps, graphs.

**Section 5: Algorithms**

Searching, sorting, hashing. Asymptotic worst case time and space complexity. Algorithm design techniques: greedy, dynamic programming and divide‐and‐conquer. Graph search, minimum spanning trees, shortest paths.

**Section 6: Theory of Computation**

Regular expressions and finite automata. Context-free grammars and push-down automata. Regular and contex-free languages, pumping lemma. Turing machines and undecidability. microprocessor and microcontroller: applications, memory and input-output interfacing; basics of data acquisition systems.

**Section 7: Compiler Design**

Lexical analysis, parsing, syntax-directed translation. Runtime environments. Intermediate code generation.

**Section 8: Operating System**

Processes, threads, inter‐process communication, concurrency and synchronization. Deadlock. CPU scheduling. Memory management and virtual memory. File systems.

**Section 9: Databases**

ER‐model. Relational model: relational algebra, tuple calculus, SQL. Integrity constraints, normal forms. File organization, indexing (e.g., B and B+ trees). Transactions and concurrency control.

**Section 10: Computer Networks**

Concept of layering. LAN technologies (Ethernet). Flow and error control techniques, switching. IPv4/IPv6, routers and routing algorithms (distance vector, link state). TCP/UDP and sockets, congestion control. Application layer protocols (DNS, SMTP, POP, FTP, HTTP). Basics of Wi-Fi. Network security: authentication, basics of public key and private key cryptography, digital signatures and certificates, firewalls.

**Section 1: Engineering Mathematics**

**Linear Algebra:** Matrix algebra, systems of linear equations, Eigen values and Eigen vectors.

**Calculus:** Functions of single variable, Limit, continuity and differentiability, Mean value theorems, Evaluation of definite and improper integrals, Partial derivatives, Total derivative, Maxima and minima, Gradient, Divergence and Curl, Vector identities, Directional derivatives, Line, Surface and Volume integrals, Stokes, Gauss and Green’s theorems.

**Differential Equations:** First order equations (linear and nonlinear), Higher order linear differential equations with constant coefficients, Cauchy’s and Euler’s equations, Initial and boundary value problems, Laplace transforms, Solutions of one dimensional heat and wave equations and Laplace equation.

**Complex variables:** Analytic functions, Cauchy’s integral theorem, Taylor series.

Probability and Statistics: Definitions of probability and sampling theorems, Conditional probability, Mean, median, mode and standard deviation, Random variables, Poisson, Normal and Binomial distributions.

Numerical Methods: Numerical solutions of linear and non-linear algebraic equations Integration by trapezoidal and Simpson’s rule, single and multi-step methods for differential equations.

**Section 2: General Engineering**

**Engineering Materials:** Structure and properties correlation;engineering materials (metals, ceramics, polymers and composites) – properties and applications; stress-strain behavior of metals and alloys;iron-carbon phase diagram, heat treatment of metals and alloys, its influence on mechanical properties.

**Applied Mechanics:** Engineering mechanics – equivalent force systems, free body concepts, equations of equilibrium; trusses; strength of materials – stress, strain and their relationship; failure theories, Mohr’s circle(stress), deflection of beams, bending and shear stress, Euler’s theory of columns.

**Theory of Machines and Design:** Analysis of planar mechanisms, cams and followers; governors and fly wheels; design of bolted, riveted and welded joints; interference/shrink fit joints; design of shafts, keys, spur gears, belt drives, brakes and clutches; pressure vessels.

**Thermal and Fluid Engineering:** Fluid mechanics – fluid statics, Bernoulli’s equation, flow through pipes, equations of continuity and momentum, capillary action, contact angle and wetting; thermodynamics – zeroth, first and second law of thermodynamics, thermodynamic system and processes, calculation of work and heat for systems and control volumes; air standard cycles; heat transfer – basic applications of conduction, convection and radiation.

**Section 3: Manufacturing Processes I**

**Casting:** types of casting processes and applications; patterns – types and materials; allowances; moulds and cores – materials, making, and testing; casting techniques of cast iron, steels and nonferrous metals and alloys; analysis of solidification and microstructure development; design of gating and riser; origin of defects.

**Metal Forming:** Stress-strain relations in elastic and plastic deformation; concept of flow stress; hot and cold working – forging, rolling, extrusion and wire drawing; sheet metal working processes – blanking, bending and deep drawing; ideal work and slab analysis; origin of metal working defects.

**Joining of materials:** Principles of fusion welding processes(manual metal arc, MIG, TIG, plasma arc, submerged arc welding processes)–different heat sources (flame, arc, resistive, laser, electron beam), and heat transfer and associated losses, flux application, feeding of filler rod; Principles of solid state welding processes (friction, explosive welding, ultrasonic welding processes); Principles of adhesive, brazing and soldering processes; Origins of welding defects.

**Powder processing:** Production of metal/ceramic powders, compaction and sintering of metals and ceramic powders.

Polymers and Composites: Plastic processing – injection, compression and blow molding, extrusion, calendaring and thermoforming; molding of composites.

**Section 4: Manufacturing Processes II**

**Machine Tools and Machining:** PBasic machine tools like centre lathe, milling machine, and drilling machine – construction and kinematics; machining processes - turning, taper turning, thread cutting, drilling, boring, milling, gear cutting, thread production, grinding; geometry of single point cutting tools, chip formation, cutting forces, specific cutting energy and power requirements, Merchant’s analysis; basis ofselection of machining parameters; tool materials, tool wear and tool life, economics of machining, thermal aspects of machining, cutting fluids, machinability; Jigs and fixtures – principles, applications, and design

**Non-traditional Manufacturing:** Principles, applications, effect of process parameters on MRR and product quality of non-traditional machining processes – USM, AJM, WJM, AWJM, EDM and Wire cut EDM, LBM, EBM, PAM, CHM, ECM.

**Computer Integrated Manufacturing:** Basic concepts of CAD – geometric modeling, CAM – CNC and robotics – configurations, drives and controls, Group Technology and its applications – CAPP, cellular manufacturing and FMS.

**Section 5: Quality and Reliability**

**Metrology and Inspection:** Limits, fits, and tolerances, gauge design, interchangeability, selective assembly; linear, angular, and form measurements(straightness, squareness, flatness, roundness, and cylindricity) by mechanical and optical methods; inspection of screw threads and gears; surface finish measurement by contact and non-contact methods;tolerance analysis in manufacturing and assembly.

**Quality management:** Quality – concept and costs; quality assurance; statistical quality control, acceptance sampling, zero defects, six sigma; total quality management; ISO 9000.

**Reliability and Maintenance:** Reliability, availability and maintainability; distribution of failure and repair times; determination of MTBF and MTTR, reliability models; determination of system reliability; preventive maintenance and replacement.

**Section 6: Industrial Engineering**

**Product Design and Development:** Principles of good product design, tolerance design; quality and cost considerations; product life cycle; standardization, simplification, diversification, value engineering and analysis, concurrent engineering; comparison of production alternatives.

**Work System Design:** Taylor’s scientific management, Gilbreths’s contributions; productivity – concepts and measurements; method study, micro-motion study, principles of motion economy; work measurement –time study, work sampling, standard data, PMTS; ergonomics; job evaluation, merit rating, incentive schemes, and wage administration.

**Facility Design:** Facility location factors and evaluation of alternate locations; types of plant layout and their evaluation; computer aided layout design techniques; assembly line balancing; materials handling systems.

**Section 7: Operations research and Operations management**

**Operation Research:** Linear programming – problem formulation, simplex method, duality and sensitivity analysis; transportation and assignment models; network flow models, constrained optimization and Lagrange multipliers; Markovian queuing models; dynamic programming; simulation – manufacturing applications.

**Engineering Economy and Costing:** Elementary cost accounting and methods of depreciation; break-even analysis, techniques for evaluation of capital investments, financial statements, time-cost trade-off, resource leveling.

**Production control:** Forecasting techniques – causal and time series models, moving average, exponential smoothing, trend and seasonality; aggregate production planning; master production scheduling; MRP and MRP-II; routing, scheduling and priority dispatching; Push and pull production systems, concept of JIT manufacturing system; Logistics, distribution, and supply chain management; Inventory – functions, costs, classifications, deterministic inventory models, quantity discount; perpetual and periodic inventory control systems.

Project management- PERT and CPM.

**Verbal Ability:**

English grammar, sentence completion, verbal analogies, word groups, Instructions, critical reasoning and verbal deduction.**Numerical Ability:**

Numerical computation, numerical estimation, numerical reasoning and data Interpretation.